Memory Funktion der Sitz/spiegeleinstellung

Diskutiere Memory Funktion der Sitz/spiegeleinstellung im Grand Cherokee WH, WK / Commander XK Forum Forum im Bereich Grand Cherokee / Commander Forum; Hi, Bin jetzt stolzer Besitzer eines Jeep GC crd 3.0 Oberland 2008 Nun habe ich folgendes Problem mit der schlüsselprogrammierung. Habe alles...
Status
Für weitere Antworten geschlossen.

GeneralCherokee

Guest
Hi,
Bin jetzt stolzer Besitzer eines Jeep GC crd 3.0 Oberland 2008
Nun habe ich folgendes Problem mit der schlüsselprogrammierung.
Habe alles laut Betriebsanleitung gemacht, trotzdem stellt sich die Sitz/spiegeleinstellung immer auf den Vorbesitzer ein.
Habe hier auch schon die Suchfunktion genutzt, leider wurde ich da nicht so richtig schlau.
Könnt ihr mit evtl. Kurz erklären wie ich es hinbekomme. Evtl wie ich die Speicherung auf der Fernbedienung löschen kann und meine eigene einspeichern kann?
Vielen dank schonmal m vorraus
Lg
 

wolke66

Guest
Moin,

klappt den grundsätzlich die Programmierung?
Heißt, stellen sich denn die SItze etc. um, wenn Du die Knöpfe 1 bzw. 2 manuell speicherst, den Sitz verstllst und dann wieder 1 bzw. 2 drückst??
 

dergero

Member
Mitglied seit
30.03.2011
Beiträge
101
Danke
2
Standort
Hannover
Moin,

hatte das selbe Problem.Bin auch nach der Betriebsanleitung vorgegangen und habe mich immer gefragt---was hast du nun wieder falsch gemacht?

Nach mehreren Versuchen war es dann gespeichert.

--- auf 1 drücken

--- alles einstellen

--- dann auf S

so ging´s bei mir.Na dann gutes gelingen und viel Spaß mit dem GC.

Gruß Gero
 
tom58

tom58

Member
Mitglied seit
27.02.2011
Beiträge
3.768
Danke
3.509
Standort
Polen/Masuren
Fahrzeug
Wk hemi und Wh crd
also bei mir geht es so: alles einstellen dann den speicherplatz drücken, 1 oder 2, und dann die taste s für speichern. dann kannst du im evic (bordcomputer) einstellen ob die einstellungen per schlüssel (fernabfrage) durchgeführt werden sollen.z.b. wenn du easy entry aktiviert hast.
 
JeepCherokeeXJ

JeepCherokeeXJ

Member
Mitglied seit
22.05.2009
Beiträge
1.284
Danke
21
Standort
72131 Ofterdingen
Also bei mir geht es so:

-alles einstellen
-S für SET drücken
-dan Spichertaste 1 o. 2 drücken. Im EVIC und MyGig wird es auch angezeigt.

Ich find die Speichersache echt klasse nur das mit der Fernbedienung ist totaler Müll. Ich weiß garnicht wie man die FB auf 1/2 einstellen kann.
 

robert.eberle

Member
Mitglied seit
09.11.2006
Beiträge
709
Danke
93
man lernt einen schlüssel an für stellung 1, z.b. den eigenen.
danach den anderen schlüssel für stellung 2, z.b. für die frau.

somit hat jeder beim öffnen alle einstellungen incl. radiosender so wie er sie braucht.

wenn man die einstellungen für verschiedene schlüssel nicht braucht, da das auto nur alleine genutzt wird braucht man den kompletten memory gedöhns nicht.
 
tom58

tom58

Member
Mitglied seit
27.02.2011
Beiträge
3.768
Danke
3.509
Standort
Polen/Masuren
Fahrzeug
Wk hemi und Wh crd
so gehts:
OPTIONAL DRIVER MEMORY SYSTEM
Once programmed, the memory buttons 1 and 2 on the driver's door panel can be used to recall the driver's seat, driver's outside mirror, adjustable brake and accelerator pedals, and radio station preset settings. Your Remote Keyless Entry transmitters can also be programmed to recall the same positions when the "Unlock" button is pressed.
Your vehicle may have been delivered with two Remote Keyless Entry transmitters. One or both transmitters can be linked to either memory position. The memory system can accommodate up to four transmitters, each one linked to either of the two memory positions.
Setting Memory Positions and Linking Remote Keyless Entry Transmitter to Memory
NOTE: Each time the SET (S) button and a numbered button (1 or 2) are pressed, you erase the memory settings for that button and store a new one.
1. Insert the ignition key and turn the ignition switch to the ON position.
2. Press the driver door memory button number 1 if you are setting the memory for driver 1, or button number 2 if you are setting the memory for driver 2. The system will recall any stored settings. Wait for the system to complete the memory recall before continuing to step 3.
3. Adjust the driver's seat, recliner, and driver's side view mirror to the desired positions.
4. Adjust the brake and accelerator pedals to the desired positions.
5. Turn on the radio and set the radio station presets (up to 10 AM and 10 FM stations can be set).
6. Turn the ignition switch to the OFF position and remove the key.
7. Press and release the SET (S) button located on the driver's door.
8. Within 5 seconds, press and release memory button 1 or 2 on the driver's door. The next step must be performed within 5 seconds if you desire to also use a Remote Keyless Entry transmitter to recall memory positions.
9. Press and release the "Lock" button on one of the transmitters.
10. Insert the ignition key and turn the ignition switch to the ON position.
11. Select "Remote Linked to Memory" in the Electronic Vehicle Information Center (EVIC) and enter "Yes" or select "Use Factory Settings" from the EVIC and enter "Yes". Refer to "Customer Programmable Features" in the Electronic Vehicle Information Center section for more information.
12. Repeat the above steps to set the next memory position using the other numbered memory button or to link another Remote Keyless Entry transmitter to memory.

Memory Position Recall
NOTE: The vehicle must be in Park to recall memory positions. If a recall is attempted when the vehicle is not in Park, a message will be displayed in the Electronic Vehicle Information Center (EVIC).
To recall the memory settings for driver one, press memory button number I on the driver's door or the "Unlock" button on the Remote Keyless Entry transmitter linked to memory position 1.
To recall the memory setting for driver two, press memory button number 2 on the driver's door or the "Unlock" button on the Remote Keyless Entry transmitter linked to memory position 2.
A recall can be cancelled by pressing any of the memory buttons on the drivers door during a recall (S, 1, or 2). When a recall is cancelled, the driver's seat, driver's mirror, and the pedals stop moving. A delay of one second will occur before another recall can be selected.

To Disable A Transmitter Linked to Memory
1. Turn the ignition switch to the OFF position and remove the key.
2. Press and release memory button number 1. The system will recall any memory settings stored in position 1. Wait for the system to complete the memory recall before continuing to step 3.
3. Press and release the memory SET (S) button located on the driver's door.
4. Within 5 seconds, press and release memory button 1 on the driver's door.
5. Within 5 seconds, press and release the "Unlock" button on the Remote Keyless Entry transmitter.
To disable another transmitter linked to either memory position, repeat steps 1-5 for each transmitter.
NOTE: Once programmed, all transmitters linked to memory can be easily enabled or disabled at one time. Refer to Remote Linked to Memory under "Customer Programmable Features" in the Electronic Vehicle Information Center (EVIC) for more information.
 

mala

Member
Mitglied seit
11.03.2011
Beiträge
63
Danke
5
Standort
Schwerte
Hallo,


bei mir hat es genau so funktioniert, wie in der Betriebsanleitung beschrieben. Natürlich auch nicht beim ersten mal.

Gruß Mario
 
tom58

tom58

Member
Mitglied seit
27.02.2011
Beiträge
3.768
Danke
3.509
Standort
Polen/Masuren
Fahrzeug
Wk hemi und Wh crd
hallo hans peter, bei mir funktioniert es wie beschrieben, allerdings lasse ich den punkt 5 weg da ich ein anderes radio habe und die presets deshalb nicht mit abspeichere.
 

robert.eberle

Member
Mitglied seit
09.11.2006
Beiträge
709
Danke
93
wichtig ist:
um die schlüssel anzulernen muß " vorher " im bc die entriegelungsfunktion eingeschaltet werden.
nach dem abspeichern " s " mit 1/2 muß mit dem entsprechenden schlüssel in vorgegebener zeit das auto verschlossen werden.

danach procedere mit dem 2 ten schlüssel wiederholen.
hat bei mir bei den jeeps immer geklappt.

mfg robert
 

mala

Member
Mitglied seit
11.03.2011
Beiträge
63
Danke
5
Standort
Schwerte
... Allerdings habt Ihr doch das Vorgängermodell vor dem Facelift ...
Oh, habe ich gar nicht drauf geachtet. Sollte das so anders sein? Ich hatte jedenfalls immer Schwierigkeiten mit den Zeitabständen zwischen den Befehlseingaben. Waren für mich einfach zu kurz (bin halt schon über 50 :))
 

mala

Member
Mitglied seit
11.03.2011
Beiträge
63
Danke
5
Standort
Schwerte
Den 50er habe ich auch längst hinter mir :wave:
Dann sind wir ja so ungefähr im selben Club. Tut's hinten links unten vorne rechts auch noch weh? (Ja? Dann ist ja noch alles da :bigsmile:) [Sorry -- Off topic]
 
Status
Für weitere Antworten geschlossen.
Thema:

Memory Funktion der Sitz/spiegeleinstellung

Memory Funktion der Sitz/spiegeleinstellung - Ähnliche Themen

  • Einstellung Fahrersitz Memory Funktion

    Einstellung Fahrersitz Memory Funktion: WK2 EZ 3-2012 - bisher keine Probleme. Auch meine Sitzeinstellung, (Memory - verbunden mit dem Schlüssel)  hat bisher gut funktioniert. Wurde von...
  • Memory Funktion defekt?

    Memory Funktion defekt?: Grüß Gott zusammen.   das Verlieren der Radiosender im Uconnect ist zwar ziemlich nervig, aber da wir eh meist Musik vom Handy hören, haben wir...
  • Memory Funktion Sitze

    Memory Funktion Sitze: Hallo   Ich habe gestern Abend mal versucht meinen Fahrersitz zu Programieren (mit Bedienungsanleitung). Man soll ja Zündschlüssel auf ON, dann...
  • Radio memory funktion

    Radio memory funktion: Hallo Freunde, Hab ein neues Radio eingebaut aber die memoryfunktion geht nicht. Die Anschlüsse wurde vorher schon auf deutsche Norm geswitched...
  • WJ memory funktion geht nicht

    WJ memory funktion geht nicht: Hallo leute hab nen problem hab nen 99 er wj hier wurden 2 neue handsender codiert jedoch die alten 2 drin gelassen jetzt sind die neuen auf...
  • Ähnliche Themen

    • Einstellung Fahrersitz Memory Funktion

      Einstellung Fahrersitz Memory Funktion: WK2 EZ 3-2012 - bisher keine Probleme. Auch meine Sitzeinstellung, (Memory - verbunden mit dem Schlüssel)  hat bisher gut funktioniert. Wurde von...
    • Memory Funktion defekt?

      Memory Funktion defekt?: Grüß Gott zusammen.   das Verlieren der Radiosender im Uconnect ist zwar ziemlich nervig, aber da wir eh meist Musik vom Handy hören, haben wir...
    • Memory Funktion Sitze

      Memory Funktion Sitze: Hallo   Ich habe gestern Abend mal versucht meinen Fahrersitz zu Programieren (mit Bedienungsanleitung). Man soll ja Zündschlüssel auf ON, dann...
    • Radio memory funktion

      Radio memory funktion: Hallo Freunde, Hab ein neues Radio eingebaut aber die memoryfunktion geht nicht. Die Anschlüsse wurde vorher schon auf deutsche Norm geswitched...
    • WJ memory funktion geht nicht

      WJ memory funktion geht nicht: Hallo leute hab nen problem hab nen 99 er wj hier wurden 2 neue handsender codiert jedoch die alten 2 drin gelassen jetzt sind die neuen auf...
    Oben